Replacing a cork or bladder pad

Replacing a Cork or Skin (Bladder) Pad
The process for replacing a pad on an oboe depends on the material. Cork requires a different technique than skin (fish bladder / baudruche). Here are the steps for replacing both types of pads yourself.
Although this delicate procedure is usually entrusted to our go-to specialist, there are times when we have to perform it ourselves in an emergency in their absence. It is therefore essential to master the steps and proper protocol.
Materials Needed
  • New replacement pads (cork and skin) of the exact diameter of the pad cup (measured accurately with a vernier caliper).
  • Stick shellac (woodwind pad shellac).
  • A small watchmaker’s screwdriver and a pair of fine, smooth-jawed flat pliers.
  • An alcohol lamp or a mini blowtorch.
  • Ungummed cigarette paper to test for air leaks.
Disassembly and Cleaning
  1. Disassemble the key in question using your screwdriver, immediately reinserting the hinge rods into their respective keys. Lay everything out in front of you on the workbench in the exact arrangement as on the instrument.
  2. Gently heat the back of the pad cup over the flame to melt the old shellac.
  3. Remove the old pad with tweezers or a toothpick.
  4. Thoroughly clean the inside of the pad cup using a cotton swab soaked in alcohol to remove all adhesive residue.
Installing the New Pad (Depending on the Type)
The main difference lies in the rigidity of cork versus the fragility of the skin (baudruche) membrane.
Stage The Cork Pad The Skin (Baudruche) Pad
Characteristics Very firm material. It must be perfectly flat and should not protrude excessively from the pad cup. A thin fish-skin membrane envelope surrounding a compressed felt disc. Very sensitive to direct heat.
Gluing Heat a stick of shellac and apply a small amount directly to the back of the cork or into the pad cup. Place a small bead of melted shellac at the bottom of the pad cup (avoid putting any on the pad itself to prevent scorching the skin).
Insertion Grasp the cork with tweezers, warm the pad cup, and insert the pad, pressing it firmly all the way to the bottom. Gently insert the pad straight into the warm pad cup. The shellac must adhere to the rear felt without soaking through it.
Fitting and Adjustment (Pad Seating)
This is the most delicate phase. The pad must rest perfectly evenly against the edges of the tone hole (on the rim of the chimney) of the instrument.
  1. Reassemble the key onto the oboe without necessarily reattaching all neighboring keys each time—only those needed to hold it in alignment between the posts are necessary. This phase is done in stages and requires successive assembly and disassembly for checking.
  2. Very briefly heat the top of the metal pad cup to slightly soften the shellac inside.
  3. Gently press the key against the tone hole rim so that the pad takes the exact seat impression of the opening.
    • For cork: You may need to use a thin paper shim behind the pad or very lightly level the cork if the balance is not perfect. Check the seating precision at the four cardinal points of the pad: they must be completely uniform. Once you identify the high or low spot, gently dress the area to be corrected on a flat sharpening stone—keeping the surface dead flat while applying ultra-light pressure to that precise spot.
    • For skin (baudruche): Be extremely gentle so as not to tear or scorch the skin during this process.
  4. Test for an airtight seal: Slide a narrow strip of cigarette paper between the pad and the tone hole rim. Close the key: as you pull on the paper, you should feel identical resistance all around the circumference of the tone hole. If the paper slides out without friction on one side, gently rewarm the pad cup and adjust the tilt of the pad.

0 Comments

Submit a Comment

Your email address will not be published. Required fields are marked *

Articles récents

A quick reference guide: the essentials at a glance for students

1. Quick Reference Guide: The Essentials at a Glance for Students 1. Basic Principles The Seesaw Effect (Principle of the Lever)Any element or key pivoting around an axis produces a reverse movement on either side of that pivot point. Lowering one end mechanically...

Cleaning and checking for wear on oboe pads

Cleaning and Inspecting the Oboe Pads for Wear The oboe’s seal depends on the integrity of the pads and the cleanliness of their surfaces where they come into contact with the rims of the tone holes. The buildup of dirt, dust, and condensation degrades the quality of...

A Practical Guide to the Student Care Kit

HAUTBOIS FUTÉ The Practical Guide to the Student Maintenance Kit This guide has been designed to support you daily after your workshop on hautboisfute.ch. It lists the essential equipment to keep in your case to prevent 95% of common issues and keep your oboe...

Diagnostic and adjustment checklist for students’ use

DIAGNOSTIC AND ADJUSTMENT CHECKLISTApplied Oboe Mechanics — Student Document Student Name: _______________________      Date: ____ / ____ / 20___ 1. Troubleshooting Protocol (By Elimination) Proceed systematically in logical order before touching any adjustment...

English glossary of terms specific to the oboe

General structure of the instrument Upper joint / Top joint Lower joint / Bottom joint Bell Tenon Components of the key and the tone hole Key Key cup (tray or dish containing the pad) Ring (or open key / brille) Post / Pillar (mounted into the body to hold the rods...

Dismantling the oboe: precautions to take

Disassembling the Oboe: Precautions to Take When partially or completely disassembling a joint of the instrument, following these simple guidelines allows you to work calmly and avoid unpleasant surprises: Choose good lighting: Work at a table with sufficient direct...

Replacing a cork tenon

Replacing a tenon cork With regular use, the corks ensuring the mechanical connection and alignment of the instrument's joints undergo structural wear (compression, drying out, or crumbling), which compromises joint stability. When this deterioration occurs, replacing...

A crack? Don’t panic!

A Crack? Don't Panic! Detecting a crack in the body of our oboe usually happens late, after the gradual onset of mechanical and acoustic symptoms: increased resistance when playing low notes, a loss of sound density, and reduced playing comfort. These issues are...

Critical simulation on my instrument

Stress Testing on My Instrument. The procedures described above are performed without risk of physical damage to the instruments. These practical exercises are staged for educational purposes on a dedicated demonstration instrument. No technical work is performed on...